Phase 2 Motortrend

P2M aluminum offset tension rods were built to allow extreme wheel angle clearance. For extreme drifters with extreme steering angles the wheel and tire might get in conflict by touching the standard...

P2M acrylic clear headlight covers for Nissan JDM S13 Silvia. Swap out the dull looking lens cover for a unique JDM look. Installation involves baking the headlight into the oven to remove the old...

P2M curved tension rods for Nissan S13 1989-94 240SX is a step up further to our existing straight tension rod. This design allows for additional wheel clearance for people that needs it with their...

P2M FLCA is constructed from S45C metal alloy for strength and rigidity. For track and drifters in mind, the FLCA collaborate the adjustment in roll center and suspension camber geometry with...

P2M solid aluminum Nissan S13 steering linkage spacer was designed to fill up the slack in the factory worn out rubber steering linkage. By using this spacer to fill up the slack will greatly improve...

P2M Nissan S13 240SX aluminum rear strut brace reinforce the rear shock tower of the chasi. This direct bolt on setup will provide additional structural rigidity to strengthen the rear part of the...

P2M Nissan S13 240SX rear bumper support brace is made from T6 6061 chambered aluminum tube, strong and light weight. Side brackets are constructed from SPHC hot rolled steel. Powder coated smooth...

P2M USDM spec interior rear floor mat set with race inspired checkered pattern in dark grey coloring. For S13 rear set of 2 pcs.

P2M USDM spec interior front carpet mat set with race inspired checkered pattern in dark grey coloring. Mats comes with signatured P2M plaque.

NOTEWhen installing please make sure to install the bracket labeled L and R in the right configurationL - LEFT DRIVER SIDE (LHD - USDM VEHICLE)R - RIGHT PASSENGER SIDE (LHD - USDM VEHICLE)

For install on the S13 1989-94 240SX, we like to flip the damper body down towards the front of the car to gain clearance for the hood. At the same time P2M S13 damper hood hinge brackets has been...

For install on the S13 1989-94 240SX, we like to flip the damper body down towards the front of the car to gain clearance for the hood. At the same time P2M S13 damper hood hinge brackets has been...

P2M S13 RLCA is made from S45C high strength alloy for strength and rigidity. The purpose is to replace the OEM arms by removing the soft rubber bushings that are most likely worned out. The adjust...

P2M Nissan S13 S14 SR20DET (RWD) LEVEL 2 ignition coil pack set is a direct replacement over the factory unit with the following improved features- Strictly produced via TS16949 certified...

P2M S13/S14 rear sway bar end links replace factory worn out bushings with stiffened urethane bushings. The end links can be installed on stock or aftermarket sway bars to get the best handling...

P2M S13/S14 front sway bar end links replace factory worn out bushings with stiffened urethane bushings. The end links can be installed on stock or aftermarket sway bars to get the best handling...

P2M billet CNC aluminum 40mm steering wheel hub for Nissan 1989-98 240SX is a perfect combo for use with aftermarket steering wheel quick release kit. The steering wheel short hub compensate the...

P2M billet CNC aluminum 40mm steering wheel hub for Nissan 1989-98 240SX is a perfect combo for use with aftermarket steering wheel quick release kit. The steering wheel short hub compensate the...

- Rear trunk mat OE fitment for RZ34 400Z- Dark grey / black checkered pattern design- Replace or overlay over the existing OE rear trunk mat

For Nissan RB25 Motor

For Nissan RB25 Motor

P2M side feed billet aluminum fuel rail kit for RB25DET. This fuel rail kit directly replaces the stock fuel rail for side feed injectors. The fuel rail is a high flow high volume over stock rail and...

OE replacement water pump for all Nissan RB25/26 Engine. This water pump was modified to accommodate both bolt hole pattern for RB25 and RB26 engine. Comes brand new with gasket and fan clutch studs.

P2M steel braided turbo line kit replaces the factory turbo hard lines on the RB25DET motor. This line kit makes it easy to work with when overhauling the turbo area where stock lines are hard to put...

- Constructed from T7 aluminum- Precision machined to fill the gap between the subframe bolt and subframe- Reduce subframe movement for improved handling and cornering which will help to reduce...

P2M rear traction (trailing links) for Nissan R35 GTR. Constructed from S45C heavy duty steel alloy with 3pc teflon self lubricated pillow ball rod ends. The rear traction links allows adjustment for...

P2M rear toe rods for Nissan R35 GTR. Constructed from heavy duty S45C steel alloy and utilize 3pc teflon self lubricated pillow ball rod ends for durability. The rear toe rods allows adjustment of...

P2M rear camber arms for Nissan R35 GTR. Made from heavy duty S45C steel alloy with 3pc self lubricated teflon lined pillow ball rod ends. Comes with pillow ball dust boot for protection against dirt...